Improvement of dimensional stability and mechanical properties of gypsum particleboard by adding white cement | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 12, Volume 30, SPRING 1 - Serial Number 50, May 2015, Pages 132-143 PDF (1.82 M) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2015.11900 | ||
| Authors | ||
| Saeed Khojasteh Khosro* ; Saeed Khojasteh Khosro; Mohammad Hasan Payan; Seyyed Mehdi Seyydi | ||
| Wood Science and Technology Department, Faculty of Civil Engineering, Shahid Rajaee Teacher Training University | ||
| Abstract | ||
| In the present research improvement of dimensional stability and mechanical properties of gypsum particleboard by using white cement was investigated. In manufacturing gypsum particleboard, Micronize gypsum was used in three levels of 2.5:1, 2.75:1 and 3:1 to dried mass of wooden materials. White cement was added in 2 levels of 5 and 10% based on oven dried mass of gypsum to reinforce gypsum particleboard properties. Water absorption, thickness swelling after 2 and 24 hours immersion in water, bending strength, modulus of elasticity and internal bond strength were measured. Vicat needle method was used to investigate the effect of adding cement on setting time of gypsum. The results showed that adding 5% cement based on oven dried mass of gypsum, increased setting time and also mechanical properties. Adding cement over than 5% (10%), significantly improved dimensional stability but reduced setting time of gypsum and mechanical properties of the boards. On the other hand, results indicated that using Micronize gypsum to 2.75 times to dried mass of wooden materials, increased bending strength and modulus of elasticity. Increasing gypsum in to 3 times, reduced bending strength and modulus of elasticity, but improved internal bond strength and dimensional stability. | ||
| Keywords | ||
| Gypsum particleboard; Micronize gypsum; White cement; Setting time of gypsum; Dimensional stability; MECHANICAL PROPERTIES | ||
| References | ||
|
-ASTM C191, 1999. Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle. -Doost Hosseini, K., 2007. Wood composite materials, Manufacturing, Aplications. 2nd ed. University of Tehran, 708 p. -Deng, Y., Furuno, T. and Wu, Y., 2001a. Effect of buffers on gypsum particleboard properties, J Wood Sci. 47:356-361. -Deng, Y.H. and Furuno, T., 2001b. Properties of gypsum particleboard reinforced with polypropylene fibers. Journal of wood science, 47(6), 445-450. -Deng, Y., Kim, H., Lei, W., Sun, Z., Jia, Y., Xuan, L. and Kim, S., 2007. Observation and analysis of gypsum particleboard using SEM. Journal of Wuhan University of Technology-Mater. Sci. Ed., 22(1): 44-47. -Deng, Y. and Furuno, T., 2002. Study on gypsum-bonded particleboard reinforced with jute fibres. Holzforschung, 56(4): 440-445. -Espinoza-Herrera, R. and Cloutier, A., 2011. Physical and mechanical properties of gypsum particleboard reinforced with Portland cement. European Journal of Wood and Wood Products, 69(2): 247-254. -EN 317, 1993. Particleboard and fiberboard - Ditermination of swelling in thickness after immersion in water. European committee for standardization. -EN 310, 1993. Wood based panels - Determination of modulus of elasticity and bending strength. European committee for standardization. -EN 319, 1993. Particleboard and fiberboard - Ditermination of tensile strength perpendicular to the plane of the board. -Kim, S., Kim, J.A., An, J.Y., Kim, H.S., Kim, H.J., Deng,Y., Feng, Q. and Luo, J., 2007. Physico‐Mechanical Properties and the TVOC Emission Factor of Gypsum Particleboards Manufactured with Pinus Massoniana and Eucalyptus Sp. Macromolecular Materials and Engineering, 292(12): 1256-1262. -Lee, B.H., Kim, H.S., Kim, S., Kim, H.J., Lee, B., Deng, Y., Feng, Q. and Luo, J., 2011. Evaluating the flammability of wood-based panels and gypsum particleboard using a cone calorimeter. Construction and Building Materials, 25(7):3044-3050. -Nazerian, M. and Kamyab, M., 2013. Gypsum-bonded particleboard manufactured from agricultural based material. Forest Science and Practice, 15(4): 325-331. -Pourjouzi, M. and Ebrahimi, GH., 2002. Important differences in some properties of gypsumboard reinforced with two type of natural fibers (Bagasse and Wood). Iranian Journal of Polymer Science and Technology, 15(4): 237-243. -Rangavar, H., Payan, M.S. and Khojasteh Khosro, S., 2014. Investigation of the type and content of gypsum on the dimensional stability and mechanical properties of gypsum particleboard, 5(1): 45-54. -Rangavar, H., 2013, Study on the possibility of recycled-banknote utilization in the production of wood gypsum composite-boards. Iranian Journal of Wood and Paper Industries, 4 (1): 87-99. -Sattler, H. and Lempfer, K., 1989. Gypsum-bonded particleboards and fiberboards. In: Moslemi AA, Hamel MP (eds) Proceedings of the Fiber and Particleboards Bonded with Inorganic Binders. Idaho, USA, p 91–93. | ||
|
Statistics Article View: 2,542 PDF Download: 1,233 |
||
Journal management system. designed by sinaweb