Studying physical and mechanical properties of two Iranian walnut wood from Noor and Shahrkord regions | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 6, Volume 38, Issue 3 - Serial Number 84, September 2023, Pages 215-224 PDF (988.42 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2023.361805.1752 | ||
| Authors | ||
| Mohammad Najafian ashrafi* 1; Mohammad Ghorbanian Far2; Esmail Rastbod3; Mohammad Salehi3; Mahdi Shamshiri4 | ||
| 1Faculty member, Department of Wood Paper Science and Industries, Imam Mohammad Baqer Technical College, Technical and Vocational University (TVU), Mazandaran, Iran | ||
| 2Lecturer of Technical and Vocational University, Department of Wood and Paper Science, Saman al-Hajj Technical College of Mashhad, Technical and Vocational University (TVU), Mashhad, Iran | ||
| 3Bachelor's degree, Department of Wood Paper Science and Industries, Technical and Vocational College No. 2, Sari, Technical and Vocational University (TVU), Mazandaran, Iran | ||
| 4Associate student, Department of Wood and Paper Science, Saman al-Hajj Technical College of Mashhad, Technical and Vocational University (TVU), Mashhad, Iran | ||
| Abstract | ||
| The walnut tree is one of the most important species in Europe, Asia and Iran, which is used in various industries such as furniture, veneer, and construction due to its high resistance and beauty. In this research, walnut trees from two different geographic locations, one from the forests in the north of Iran (Noor) and the other in the west of Iran (Shahrkord), were selected. We studied physical properties including dry density, basic density, shrinkage, and mechanical properties including bending strength, modulus of elasticity, compression parallel to the grain, shear, tensile parallel and perpendicular to the grain, tangential and radial screw withdrawal strength and toughness. In this research, standards 3129 and ASTM D143-14 were used to perform physical and mechanical tests, respectively. The moisture content of all samples during mechanical tests was 12%. The average dry density of Noor and Shahrekord walnuts was 0.61 and 0.57 (g/cm3) respectively. The results of variance analysis showed that the characteristics and physical resistances of these two species were not significantly different except for dry density, radial, tangential and volumetric shrinkages. However, due to the higher density of Noor species, it showed higher mechanical resistance compared to the Shahrekord species. | ||
| Keywords | ||
| walnut; mechanical properties; physical properties | ||
| References | ||
|
-Bachtiar, E.V., Rüggeberg, M., Hering, S., Kaliske, M. and Niemz, P., 2017. Estimating shear properties of walnut wood: a combined experimental and theoretical approach. Materials and Structures 50:1-15.
-Bachtiar, E.V., Rüggeberg, M. and Niemz, P., 2018. Mechanical behavior of walnut (Juglans regia L.) and cherry (Prunus avium L.) wood in tension and compression in all anatomical directions. Revisiting the tensile/compressive stiffness ratios of wood. Holzforschung 72:71-80.
-Bachtiar, E.V., Sanabria, S.J., Mittig, J.P. and Niemz, P., 2017. Moisture-dependent elastic characteristics of walnut and cherry wood by means of mechanical and ultrasonic test incorporating three different ultrasound data evaluation techniques. Wood Science and Technology 51:47-67.
-Bolling, B.W., Chen, C.-Y.O., McKay, D.L. and Blumberg, J.B., 2011. Tree nut phytochemicals: composition, antioxidant capacity, bioactivity, impact factors. A systematic review of almonds, Brazils, cashews, hazelnuts, macadamias, pecans, pine nuts, pistachios and walnuts. Nutrition research reviews 24:244-75.
-Cambria, D. and Pierangeli, D., 2012. Application of a life cycle assessment to walnut tree (Juglans regia L.) high quality wood production: a case study in southern Italy. Journal of Cleaner Production 23:37-46.
-Castro, G., Bergante, S., Sansone, D., Bidini, C. and Pelleri, F., 2019. Common walnut (Juglans regia L.) wood characteristics in two Italian plantations. Annals of Silvicultural Research 43:35-40.
-Fathi, H., Nasir, V., Kazemirad, S., 2020. Prediction of the mechanical properties of wood using guided wave propagation and machine learning. Construction and Building Materials 262:120848.
-Guler, C. and Dilek, B., 2020. Investigation of High-frequency Vacuum Drying on Physical and Mechanical Properties of Common Oak (Quercus robur) and Common Walnut (Juglans regia) Lumber. BioResources 15.
-Harte, A.M., 2017. Mass timber–the emergence of a modern construction material. Journal of Structural Integrity and Maintenance 2:121-32.
-Hemery, G.E., Savill, P.S. and Thakur, A., 2005. Height growth and flushing in common walnut (Juglans regia L.): 5-year results from provenance trials in Great Britain. Forestry 78:121-33.
-Pollegioni, P., Woeste, K.E., Chiocchini, F., Olimpieri, I., Tortolano, V., Clark, J., Hemery, G.E., Mapelli, S. and Malvolti, M.E., 2014. Landscape genetics of Persian walnut (Juglans regia L.) across its Asian range. Tree Genetics & Genomes 10:1027-43.
-Ramage, M.H., Burridge, H., Busse-Wicher, M., Fereday, G., Reynolds, T., Shah, D.U., Wu, G., Yu, L. and Fleming, P., 2017. The wood from the trees: The use of timber in construction. Renewable and Sustainable Energy Reviews 68:333-59.
-Sadoh, T. and Christensen, G., 1967. Longitudinal shrinkage of wood—Part I: Longitudinal shrinkage of thin sections. Wood Science and Technology 1:26-44.
-Standovár, T. Kenderes, K., 2003. A review on natural stand dynamics in beechwoods of East Central Europe. Applied ecology and environmental research 1:19-46.
-Yu, L., Liang, Y., Zhang, Y. and Cao, J., 2020. Mechanical properties of wood materials using near-infrared spectroscopy based on correlation local embedding and partial least-squares. Journal of forestry research 31:1053-60.
-Zhang, S., 1997. Wood specific gravity-mechanical property relationship at species level. Wood Science and Technology 31:181-91. | ||
|
Statistics Article View: 644 PDF Download: 425 |
||
Journal management system. designed by sinaweb