| تعداد نشریات | 282 |
| تعداد نشریات سازمان | 80 |
| تعداد شمارهها | 3,220 |
| تعداد مقالات | 35,690 |
| تعداد مشاهده مقاله | 53,578,756 |
| تعداد دریافت فایل اصل مقاله | 92,857,223 |
مطالعه آزمایشگاهی خصوصیات هیدرولیکی جریان در سرریزهای مدور قائم با ورودی پاپیونی شکل | ||
| تحقیقات مهندسی سازه های آبیاری و زهکشی | ||
| دوره 22، شماره 85، فروردین 1401، صفحه 41-58 اصل مقاله (1.19 M) | ||
| نوع مقاله: مقاله پژوهشی | ||
| شناسه دیجیتال (DOI): 10.22092/idser.2022.357719.1501 | ||
| نویسندگان | ||
| سمیرا طالبی1؛ قربان مهتابی* 2؛ مسعود کرباسی3؛ مسعود اکبری4 | ||
| 1کارشناسی ارشد سازههای آبی؛ گروه مهندسی آب، دانشگاه زنجان، ایران | ||
| 2استادیار گروه مهندسی آب، دانشگاه زنجان، ایران | ||
| 3دانشیار گروه مهندسی آب، دانشگاه زنجان، ایران | ||
| 4دکتری سازه های آبی، دانشگاه تبریز، تبریز، ایران | ||
| چکیده | ||
| در سدهای مخزنی، یکی از روشهای افزایش دبی عبوری سرریزهای مدور قائم و کاهش شرایط وقوع جریانهای گردابی، اصلاح شکل ورودی سرریز میباشد. برای رسیدن به این هدف، سرریز با ورودی نیلوفری، گلبرگی، کلید پیانویی و زیگزاگی پیشنهاد شده است. در این تحقیق شکل جدید ورودی سرریزهای مدور قائم به فرم پاپیونی معرفی شد و با انجام یک سری آزمایش، ضریب دبی جریان در این نوع سرریزها مطالعه شد. سرریزهای پاپیونی با زوایای مختلف پاپیون (60 تا 150 درجه) در دو حالت وجود کمان میانی و بدون آن (با طول کلی یکسان سرریز) استفاده و نتایج حاصل با یک سرریز نیلوفری مقایسه شد. نتایج نشان داد که در مدلهای پاپیونی بدون کمان میانی، افزایش زاویه پاپیون منجر به کاهش تداخل جریان و افزایش دبی عبوری از سرریز میشود، به طوریکه مدل B-150 (با زاویه بین پاپیون برابر 150 درجه) دارای ضریب دبی بالاتری نسبت به سایر مدلهای پاپیونی بود. این مدل سرریز پاپیونی نسبت به سرریز نیلوفری نیز دارای عملکرد هیدرولیکی بهتری بود (10 درصد). همچنین مزیت اقتصادی آن نسبت به سرریز نیلوفری بالاتر بود (31 درصد). در مدلهای پاپیونی با کمان میانی، تغییر زاویه پاپیون برروی ضریب دبی جریان اثر محسوسی نداشت و عملکرد هیدرولیکی آنها نسبت به سرریز نیلوفری پایین تر بود (9/7-5/3 درصد). | ||
| کلیدواژهها | ||
| سرریز پاپیونی؛ سرریز نیلوفری؛ شفت قائم؛ ضریب دبی | ||
| عنوان مقاله [English] | ||
| Experimental Study of Hydraulic Properties of Flow over Vertical Shaft Spillway with Bow-Tied Shape Inlet | ||
| نویسندگان [English] | ||
| Samira Talebi1؛ Ghorban Mahtabi2؛ Masoud Karbasi3؛ Masoud Akbari4 | ||
| 1University | ||
| 2Assistant professor, water engineering department, University of Zanjan, Zanjan, Iran | ||
| 3Associate professor - university of Zanjan | ||
| 4University of Tabriz | ||
| چکیده [English] | ||
| Extended Abstract Experimental Study of Hydraulic Properties of Flow over Vertical Shaft Spillway with Bow-Tied Shape Inlet Introduction A spillway is a structure used to provide the controlled release of water from a dam or levee downstream, typically into the riverbed of the dammed river itself. One of the types of spillway used in dams is vertical shaft spillway or the same as morning glory spillway. One of the methods to increase the flow rate and reduce the occurrence of vortex currents in the spillway is to modify the shape of the inlet of the spillways. In recent years, spillways with daisy, piano key and zigzag inlets have been proposed known as spiral spillways. A review of the results of previous research shows that the common goal in the study of vertical shaft spillways is to pass the flood flows with the highest possible discharge and the lowest water level and reducing the eff destructive effects of vortex currents. In previous researches, issues such as the effect of the inlet type of vertical shaft spillway and geometric parameters of the structure on the discharge coefficient and the study of vortex occurrence conditions and hydraulic flow of vertical shaft spillway. In this research a new shape of vertical shaft inlet in form of Bow-tied spillway was introduced and discharge coefficient of these spillways was investigated using a series of experiments. Methodology The experiments of this research were performed in a metal cube tank with 1.5 m length, 1 m height and 1 m width with transparent Plexiglas side walls in the hydraulic laboratory of Department of Water Engineering at Zanjan University. Bow-tied spillways were examined with different angles of the bow-tie (60-150 degree) in both cases of with middle arc and without middle arc and the results were compared with a morning glory spillway. In this research, by preparing eight bow-tie spillways and a morning glory spillway with a total length of 60 cm and considering the hydraulic conditions (H/D), 72 experiments were run to investigate the effect of the geometric shape of the spillway on the discharge coefficient. Results and Discussion Results showed that in Bow-tied models without middle arc, increase of the bow-tie angle leads to reduce the flow interference and increase of flow discharge over the spillway. So that B-150 model (with 150 bow-tie angle) had higher discharge coefficient than the other models of bow-tied. This model had better hydraulic performance than morning glory spillway (10 percent). Also, economic advantage of this model was higher than morning glory spillway (31 percent). Results of the tip position of the bow-tie spillway show in tip angle of 120 degree, the tip position of the bow-tie has a significant effect on the discharge coefficient of the spillway, but with increasing the bow tip angle from 120 to 150, the tip position of the bow-tie spillway did not have much effect on the discharge coefficient. In Bow-tied models with middle arc, change of bow-tie angle had no significant effect on discharge coefficient and hydraulic performance of these models was lower than morning glory spillway (5.3-9.7). This could be due to the interference of fall currents and the low internal area of these models. Conclusions Comparison of the hydraulic performance of bow-tie models with morning glory spillway shows that the B-150 model has the highest hydraulic performance (10%) compared to other models. On the other hand, this spillway has a better economic advantage (31%) than the morning glory spillway. In the construction of reservoir dams, especially earthen dams, the major part of the executive cost is related to the implementation of concrete structures of emergency spillway. In this situation, by choosing Bow-tied spillway with optimal geometry, a suitable economic savings can be achieved along with improving the hydraulic conditions of the flow. Keywords: Bow-tied spillway , Discharge coefficient, Morning glory spillway, Vertical shaft | ||
| کلیدواژهها [English] | ||
| Bow-tied spillway, Discharge coefficient, Morning glory spillway, Vertical shaft | ||
| مراجع | ||
|
Anwar, H. O., Waller, J. A., & Amphlet, M. B. (1978). Similarity of free-vortex at horizontal intake. Journal of Hydraulic Research, 16(2), 95–105.
Bagheri, A., M. S. Bajestan, H. M. Jahromi, H. Kashkooli & H. Sedghee. (2010). Hydraulic evaluation of the flow over polyhedral morning glory spillways. World Applied Sciences Journal, 9(7), 712-717.
Djillali, K. Abderrezak, B. Petrovic, G.A. & Sourenevna B. E. (2021). Discharge capacity of shaft spillway with a polygonal section: a case study of Djedra dam (East Algeria). Water Supply, 21 (3), 1202–1215.
Jain, A. K., Raju, K. G., & Garde, R. J. (1978). Vortex formation at vertical pipe intakes. Journal of Hydraulic Division ASCE, 104(10), 1429–1445.
Kabiri-Samani, A. R. & Keihanpour, M. (2020). Hydraulic characteristics of swirling flow at shaft spillways with the marguerite-shaped inlets. Journal of Hydraulic Research, 59(5), 1-15.
Lashkar-Ara, B & Sheikhi, Y. (2017). Introduce of CPK Spillway and Study of Its Discharge Coefficient under Free Flow Regime. Irrigation Sciences and Engineering, 40(2), 209-221. (In Persian)
MirHoseini, S. (2012). Hydraulic charactristics of flow in vertical shaft spillways with Piano-Key inlet (M.Sc. Thesis). Department of Civil Engineering, Isfahan University of Technology, Isfahan, Iran. (In Persian)
Mojadami, M.J. & Kabiri-Samani, A.R. (2016). Effects of Daisy-Shape Inlet on Free Flow over Shaft Spillways. Modares Civil Engineering Journal, 16(5), 191-202. (In Persian)
Nasiri, S., A. Kabiri-Samani, A., & Asghari, K. (2016). Numerical Modeling of Flow Field around the Shaft Spillways Using Piano-Key Inlet. Journal of Hydraulics, 11(1), 53-66. (In Persian)
Rouzegar, J., Kamanbedast, A. A. Masjedi, A., Heidarnejad, M. & Bordbar, A. (2019). The Influence of Inlet Section Geometry in Labyrinth-Morning Glory Spillways with and without Vortex Blade on Discharge Coefficient. Journal of Water and Soil Science, 23(3), 209-221. (In Persian)
Sabeti, P., Hojat Karami, H. & Sarkardeh, H. (2019). Analysis of the Impact of Effective Length of Morning Glory Spillway on Its Performance (Numerical Study). Instrumentation Mesure Métrologie, 18(2), 211-221.
Schleiss A. J. (2011). From labyrinth to piano key weirs. Ecolepoly technique Federal de Lausanne.
Shemshi, R. (2012). Effects of Piano-Key inlet on flow hydraulic characteristics at vertical shaft spillways (M.Sc. Thesis). Department of Civil Engineering, Isfahan University of Technology, Isfahan, Iran. (In Persian)
Shemshi, R. & Kabiri-Samani A. R. (2016). Swirling flow at vertical shaft spillways with circular piano-key inlets. Journal of Hydraulic Research, 55(2), 1-11.
USBR. (1987). Design of small dams .3rd Edition, U.S. Bureau of Reclamation.
Wayne Coleman, H. Wei, C. Y. & Lindell, J. E. (2004). Hydraulic design of spillway. McGrawHill.
| ||
|
آمار تعداد مشاهده مقاله: 857 تعداد دریافت فایل اصل مقاله: 445 |
||