Investigation on Plane Carbon Steel “CK45” for Using in Tillage Tools | ||
| تحقیقات مهندسی صنایع غذایی | ||
| Article 2, Volume 5, Issue 2, January 0, Pages 15-26 PDF (276.84 K) | ||
| Document Type: Research Paper | ||
| Abstract | ||
| The plain carbon steel “CK45” has relatively well mechanical and metallurgical properties and low cost. The purpose of this research was the property evaluation of this steel on abrasive wear and impact for using in plows and other tillage tools. Tillage tool should resist in abrasive wear and impact simultaneously. Several heat treatments were done on specimens of this steel. A standard test device for abrasive wear “Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests, G105-89” was made. This device and standard charpy test apparatus determined the abrasive and impact resistance, respectively. Results showed that the impact and abrasive resistance of this steel can be improved by simple heat treatment and used properly for tillage tools. | ||
| Keywords | ||
| Abrasive wear; heat treatment; Impact resistance; Plane Carbon Steen “CK45”; Tillage Tools | ||
| References | ||
|
1- احمدی، ج.، منیر واقفی، م.، صالحی، م. و نیرومند، ب. 1382. بررسی رفتار سایشی خراشان سه جسمی فولاد یوتکتوئیدی. مجموعه مقالات پنجمین همایش ملی مهندسی سطح و عملیات حرارتی. تهران. 2- Avner, S. H. 1974. Introduction to physical metallurgy. 2nd Ed. NewYork: Mcgraw-Hill. U. S. A.
3- Chandler, H. 1998. Heat treater,s guide, Practices and procedures for irons and steels. 2nd Ed. ASM International. U. S. A.
4- Chen, Y. T., Tong, J., Ren, L. Q., Chen, B. C., Ge, L. H. 1994. Abrasive wear behaviour of several soil adhesion reducing materials. Transactions of the Chinese Society of Agricultural Engineering. 10, 91-5.
5- Das, S., Prasad, B. K., Jha, A. K., Modi, O. P. and Yegneswaran, A. H. 1993. Three body abrasive wear of 0.98% carbon steel. Wear. 162-164, 802-810.
6- Davis, J. R. 2001. Surface engineering for corrosion and wear resistance. 2nd Ed. Ohio, ASM International. U. S. A.
7- Foley, A. G. 1984. Abrasive wear of cultivation equipment by soil. Soil and Water. 12: 2, 12-14. 8- Hutchings, I. M. 1992. Tribology: Friction and wear of engineering materials, 1st Ed. London, Edward Arnold. U. K.
9- Kepner, R. A., Bainer, R. and Barger, E. L. 1982. Principles of Farm machinery, 3rd Ed. Westport, AVI. U. S. A.
10- Khruschov, M. M. 1974. Priciples of abrasive wear. Wear. 28, 69-88.
11- McLees, V. A. and Chisholm, C. J. 1989. Hard materials for soil cutting edges. Assessment of different grades of tungsten carbide under field conditions. Divisional Note AFRC Institute of Engineering Research. UK. 1502: 1-24.
12- Packer, I. J. and Roberts, J. H. 1989. Tungsten carbide protection of tillage points. Agricultural Engineering Australia. 18, 123-32.
13- Polak, M., Bily, J. and Seckar, P. 1988. The effect of nitration on the resistance of mouldboards to abrasive wear. Zemedelska Technika. 34:9, 541-8.
14- Prasad, B. K. and Parsad, S. V. 1991. Abrasion induced microstructural changes during low stress abrasion of a plain carbon (0.5%) steel. Wear. 151, 1-12.
15- Rabinowicz, E. 1995. Friction and wear of materials, 2nd Ed. John Wiley and Sons. U. S. A.
16- Scheffler, O. and Allen, C. 1988. The abrasive wear of steels in South African soils. Tribology International. 21: 3, 127-135.
17- Standard Test Method for ConductingWet Sand/Rubber Wheel Abrasion Tests, G105-89. Annual book of ASTM standards. 2002. Philadelphia. Vol 3.02, 443-451. U. S. A. 18- Standard Test Method for Rubber Property-Durometer Hardness. D2240- 95. Annual book of ASTM standards. 1996. Philadelphia. Vol 9. 01, 403-406. U. S. A.
19- Test Method for Notched Bar Impact Testing for Mettalic Materials, E23 - 98. Annual book of ASTM standards. 1999. Philadelphia. Vol 3.01, 138-162. U. S. A.
20- Test Method for Vickers Hardness of Mettalic Materials, E92 – 82. 1997. Annual book of ASTM standards. 1999. Philadelphia. Vol 3. 01, 216-224. U. S. A.
21- Tian, Z. X., Sun, W. L., Shang, M. Y., Jiang, X. C., Han, W. X. and Wang, M. H. 1989. Application of boronizing technology on ploughshares and study on the abrasive wear characteristics under low stress of boronized layer. Potentialities of Agricultural Engineering in Rural Development. 248-9.
22- Wang, Y. and Lei, T. 1996. Wear behavior of steel 1080 with different microstructures during dry sliding. Wear. 194, 44-53.
23- Xu, B., Feng, C. M. and Song, Y. P. 1998. Experiment and study on improving the abrasive wear resistance of steel by re-chrome-boronizing. Transactions of the Chinese Society of Agricultural Engineering. 14: 3, 163-7.
24- Yu, H. J. and Bhole, S. D. 1990. Development of a prototype abrasive wear tester for tillage tool materials. Tribology International. 23: 5, 309-316.
25- Zhang, J. and Kushwaha, R. L. 1995. Wear and draft of cultivator sweeps with hardened edges. Canadian Agricultureal Engineering. 37: 1, 41-47. | ||
|
Statistics Article View: 1,257 PDF Download: 633 |
||
Journal management system. designed by sinaweb