Investigation on the Effects of humidity and heat of combined papers on quality of CorrugatedBoard | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 14, Volume 25, Issue 2 - Serial Number 33, September 2018, Pages 309-320 PDF (258.75 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2010.117317 | ||
| Authors | ||
| Jafar Ebrahimpoor kasmani* 1; Amir mohssen Nazeri2; Ali Ashryeh3 | ||
| 1Scientific member of Islamic Azad University- Savad kooh, Branch. | ||
| 2Graduated student of MSc. of Wood &Paper Science,faculty of Natural Resources,Tehran Azad University, Science &Reaserch Campus - Q.C Manager of Towhid Carton Co. | ||
| 3MSc. Student of Wood and Paper, faculty of Natural Resources,Chalous Azad University Campus. | ||
| Abstract | ||
| In this investigation , effects of different humidity and heat on quality of Corrugated board , was studied , and optimum treatment indicated Variables in this Paper was : Corrugator speed (50,100,150m/min) ,wraping angle of the paper around preheaters (90,180,300 degree) and moisture of paper (6.5%,7%,8.5%). Papers that treated for this purpose was included : 125gsm kraft liner ,127 gsm medium paper and 140gsm test liner paper. A flut type of 3ply Corugated board was selected for this study.Moisture of paper was measured in 3 places : Paper on roll stand before single facer , paper after singlefacer preheater and paper before incoming doublefacer in hot plate unit. Also temprature was measured in corrugator rolls ,hot Plates in double facer and final Board after Exiting of the Machine. Results show that , warp of final board decreased in speed 50 and 100m/min ,moisture 7% and 1800 wraping angle of the paper around preheater. That means lower speeds and higher wraping angles cause to more heat on corrugated board and decreasing in warp content resulted.It should be noted that lower humidity more than 7% and increase wraping angle more than 180 degree cause to over drying and intensive moisture decrease in final board that cause to reverse warp in final board. | ||
| Keywords | ||
| Corrugatedboard; humidity; heat; liner paper; Medium paper; warp | ||
| References | ||
|
1-Swedish Association of pulp and paper Engineers(1987),
"Improving efficiency in the Drying of paper and board".
Report No.EMR/IEA/PP7/SPCI/Stockholm,NOV.1987.
2-Kerleker,B.V & Desmond, R.M.(1977),"Engineering Heat Transfer" west publishing
NewYork,1977,p.394.
3-Gavelin ,N.G (1972)"Drying of paper and paper Board".
Lockwood , Newyork1972.P.19
4-Bruce Taylor (1999). "Interaction of moisture and Humidity on Corrugated Board Quality" Corrugating International Vol.1,No.3(1999).
5-Nissan,A.H.(1956)"The Rheological Properties of cellulose sheets" .Retrospect and Synthesis. Tappi39(2),93-97(1956).
6-De. Ruvo,A.et al(1976)"The influences of Temprature and Humidity on the Elastic and Expansional propertise of paper" The British paper and Board Industry federation 1976.VOL.2/785-810.
7-Page,D.H.& Tydeman,P.A (1962)"A New Theory of the shrinkage , Structure of paper". Symposium held at oxford,Sep.1962,VOL.1.397-421.
8-Nordman,L(1958). "laboratory Investigations into the dimensional stability of paper".
Tappi,41(1)-23-30(1958).
9-Kilzer,F.J(1971)."Thermal Degradation of cellulose and celloluse" Derivatives, willey Interscience, Newyork VOL.5,1971,10471078.
10-Luner.P & Cardwell (1976)."Thermomechanical Stability of pulp and paper" British paper and Board Industry federation,1976.VOL.2,724-752. | ||
|
Statistics Article View: 537 PDF Download: 1,731 |
||
Journal management system. designed by sinaweb