Investigating the bending strength of wooden pin in H-shaped joints in MDF | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 4, Volume 27, Issue 3 - Serial Number 40, September 2012, Pages 423-433 PDF (211.39 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2012.116106 | ||
| Authors | ||
| amir lashgari* 1; Mohssen Ahmadi2 | ||
| 1Assistant professor, Islamic Azad University, Karaj Branch. Department of Wood and Paper Science and Technology, Karaj, Iran. | ||
| 2M.Sc., Wood and Paper Science and Technology, Islamic Azad University, Karaj Branch, Karaj, Iran | ||
| Abstract | ||
| Aim of this study were to examine the effects of pin diameter (6, 8 and 10 millimeter), the pins interval ( 30,50 and 70 millimeter), wooden pin penetration depth (2d,3d and 4d D=Diameter of pin) and the shape of H joint on bending strength of the joint. In order to make the H joints, the dimension of the middle member was selected as 200x125x16 millimeter and the dimension of the side members were selected as 250x125x16 millimeter. MDF was used to make the joints. The wooden pin used in the present research was made from hornbeam (Carpinus betulus) which is common pin in the market. PVA glue was used to make pin joints. Twenty seven treatments were obtained out of various combinations of the variables and considering four replication for each treatment, 108 H-shaped samples were prepared. The bending strength of the joints was measured. The results from mechanical test indicated that for each pin penetration depths in H joint, increasing the distance between pins, the bending strength decreased. Maximum bending strength was related to the pins having diameter of 10 millimeter. In 4d penetration depth, for each three diameters of 6, 8 and 10 millimeter, the maximum bending strength was reached on 30 millimeter intervals. The minimum bending strength for the pin having 6 millimeter diameter was obtained in the interval of 10 millimeter. The same results were obtained for the 2d and 3d penetration depths. | ||
| Keywords | ||
| dowel joint; wooden pin; H- joint; Bending strength; MDF; PVA | ||
| References | ||
|
- لشگری،امیر؛(1387). بررسی مقاومت کششی و گشتاور خمشی در اتصال دوبل سازه های چوبی،دو فصل نامه علمی پژوهشی تحقیقات علوم چوب و کاغذ ایران،صفحه10. - نوری،حبیب ؛(1382).بررسی مقاومت کششی و برشی اتصال دوبل در تخته خرده چوب ، پایان نامه کارشناسی ارشد صنایع چوب و کاغذ، دانشکده منابع طبیعی دانشگاه تربیت مدرس، صفحه115. - نوری،حبیب؛(1383).بررسی مقاومت برشی اتصال دوبل در تخته خرده چوب ، پایان نامه کارشناسی ارشد صنایع چوب و کاغذ، دانشکده منابع طبیعی دانشگاه تربیت مدرس،صفحه115. - نوری،حبیب؛(1388)بررسی مقاومت برشی جانبی انواع اتصال های دوبل چوبی،پیچ و الیت در MDF دو فصل نامه علمی پژوهشی تحقیقات علوم چوب و کاغذ ایران،صفحه10. -Chou ,C.hung,C.(1998).Effects of hygroscopic treatment on bending strength of dowel joints. Adhesive technology and bonded tropical wood production Vol.29,p.602-605
-Eckelman,C.A. assenos,D.L. forest products journal.(1985).Vol.35 (5).55.
-Eckelman,C.A.forest products journal.(1969).No.29 (1),48.
-Eckelman,C.A. Edrill,Y. Zhang,J.(2002)."Withdrawal and strength of dowel joints construction of plywood and oriented strand board ". Forest products journal, Vol.52,No.9,p66-74.
-Guan,E. and wand Rod,P.D.(2000).Structural Timber Research unit. University of Brighton .Brighton BN24 Go.
-Guntekin,E. performances of furniture joints ready for fitting.(2004).wood technical turkey (5).17-21.
-Rammer, D.(1999).parallel to grain dowel bearing strength of two Guatemalan hard woods. Forest product journal, Vol 49, No.6, p77-78.
-Somchai, V.(1998).Strength of tenon and dowel joints in teak. F. Bangkok,106 leaves.
-Wilkinson TL.(1991)." Dowel bearing strength. Research paper forest products laboratory". No.FPL-rp-505,9p.
-Zhang, J. Edrill Y. Eckleman C. (2002). "Lateral holding strength of dowel joints construction of plywood and oriented strand board". Forest products journal,Vol.52,No.7/8,p 83-88. | ||
|
Statistics Article View: 562 PDF Download: 482 |
||
Journal management system. designed by sinaweb