Investigation on withdrawal capacity of staple in the upholstered furniture frame made of LVL | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 2, Volume 32, Issue 2 - Serial Number 59, July 2017, Pages 171-180 PDF (278.91 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2017.109762 | ||
| Authors | ||
| Mosayeb Dalvand1; Ghanbar Ebrahimi2; Kambiz Pourtahmasi* 3 | ||
| 1PhD. Student, Department of Wood and Paper Science & Technology, Faculty of Natural Resources, University of Tehran, Iran | ||
| 2Professor, Department of Wood and Paper Science & Technology, Faculty of Natural Resources, University of Tehran, Iran | ||
| 3Professor, Department of Wood and Paper Science & Technology, Faculty of Natural Resources, University of Tehran, Iran | ||
| Abstract | ||
| In this study effect of staple length (penetration length) and its number in connection, on withdrawal capacity in face and edge of laminated veneer lumber (LVL) out of poplar was investigated. In this investigation, the staple with 3 and 4 cm penetration length and staple with 3, 4 and 5 cm penetration length for withdrawal capacity in face and edge were used respectively. Number of staples at 4 levels (2, 3, 4 and 5) were chosen as a variable. Results have shown that withdrawal capacity in face significantly increases with increase of penetration length. Withdrawal capacity in edge increases drastically with increase of penetration length from 3 to 4 cm, but increase in penetration length from 4 to 5 cm had no significant effect. Withdrawal strength capacity in face has increased with increase of staples number. But, increase of staple number had no significant effect on withdrawal strength capacity in edge. Maximum withdrawal capacity was observed in joints fabricated with penetration length of staple 4 cm and number of 5 staples in face and minimum those were observed with penetration length 3 cm and number of 2 staples in edge. | ||
| Keywords | ||
| Withdrawal strength capacity; Upholstered furniture; Staple; LAMINATED VENEER LUMBER | ||
| References | ||
|
- Ebrahimi, G., 2007. Engineering design of furniture structure. Tehran university publication, 491 Pages. (In Persian). - Erdil, Y.Z., Zhang, J., and Eckelman C.A., 2003. Staple holding strength of furniture frame joints constructed of plywood and oriented strandboard, Forest Products Journal, 53(1): 70-75. - Dalvand, M., Ebrahimi, GH., Rostampour Haftkhani, A., and Maleki, S., 2013. Analysis of factors affecting diagonal tension and compression capacity of corner joints in furniture frames fabricated with dovetail key, Journal of Forestry Research, 24(1): 155−168. - Atar, M., and Ozcifci, A., 2008. The effects of screw and back panels on the strength of corner joints in case furniture, Materials and Design, 29: 519–525. - Atar, M., Ozcifci, A., Altinok, M., Celikel, U., 2009. Determination of diagonal compression and tension performances for case furniture corner joints constructed with wood biscuits, Materials & Design, 30(3): 665–670. - Cai, L., Wang, F., and Tan, H., 1995. Study on the strength of moltinject corner joints of furniture, Holz als Roh- und Werkstoff, 53: 385-388. - Dalvand M, Ebrahimi GH, Rostampour Haftkhani, A., and Maleki, S., 2012. Analysis of factors affecting diagonal tension and compression capacity of corner joints in furniture frame fabricatedwith dovetail key, Journal of Forestry Research, 24(1): 155−168. - Eckelman, C.A., 1993. Potential uses of laminated veneer lumber in furniture. Forest Products Journal, 43(4): 19–24. - Ratnasingam, J., and Ioras, F., 2013. Effect of adhesive type and glue-line thickness on the fatigue strength of mortise and tenon furniture joints, European Journal of Wood and Wood Products, 71(6): 819–821. - Ratnasingam, J., and Ioras, F., 2015. The fatigue characteristics of two-pin moment-resisting dowelfurniture joints with different assembly time and glueline thickness, European Journal of Wood and Wood Products, 73(2): 279–281. - Standard test methods for Mechanical fasteners in wood, 2008. Annual Book of ASTM Standard, D 1761–88, - Tankut, A. N., and Tankut, N., 2010. Evaluation the effects of edge banding type and thickness on the strength of corner joints in case-type furniture, Materials & Design, 31(6): 2956–2963. - Vassiliou, V., and Barboutis, I., 2005. Screw withdrawal capacity used in the eccentric joints of cabinet furniture connectors in particleboard and MDF, Journal of Wood Science, 51: 572-576. -Wang, H., Mohammad, M., Salenikovich, A., Knudson, R. M., and Zhang, J., 2007. Fatigue bending resistance of metal-plated joints constructed of oriented strandboard for upholstered furniture frames, Forest Products Journal, 57(11):59-63. | ||
|
Statistics Article View: 861 PDF Download: 601 |
||
Journal management system. designed by sinaweb