Investigation on the effect of different methods of applying transparent coatings on adhesion strength of coating in wooden surfaces | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 7, Volume 31, Summer 2 - Serial Number 55, May 2016, Pages 248-260 PDF (404.92 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2016.105773 | ||
| Authors | ||
| Mohammad Ghofrani; Zahra Mohammad Moradi; Saeed Khojasteh Khosro* | ||
| M.Sc., Wood Science and Technology Department, The Faculty of Civil Engineering, Shahid Rajaee Teacher Training University | ||
| Abstract | ||
| In present study the effect of different methods of applying transparent coatings on adhesion strength of coating in Walnut (Juglans regia), Maple (Acer velutinum) and Pine (Pinus eldarica) species was investigated. For this purpose, samples prepared with dimension of 200×100×20 mm and 8% moisture content. Samples’ surfaces were sanded with 100, 120 and 180 grate sizes sandpaper significantly. Then after preparation wooden samples with sealer, their surfaces covered with clear and acid catalyzed transparent finish in separate process by using spray gun and applicator. Adhesion strength of coating was measured with Pull-Off method based on ASTM D4541 standard. Fluorescence microscopy test used for investigation coating penetration in spray gun and applicator method. Results showed that the method of applying coating on wooden surfaces has significantly affected adhesion strength, and highest adhesion strength between all samples, observed in samples coated with applicator method. Investigation of coating penetration indicated that applicator method had good penetration in wood substrate in comparison spray gun method. Highest differences in adhesion strength of coating between spray gun and applicator method were observed in Walnut and Maple’s samples. In general, highest adhesion strength of coating was found in Walnut samples covered with acid catalyzed transparent finish by using applicator method. | ||
| Keywords | ||
| Transparent coatings; Adhesion strength of coating; Penetration of coating; Coating applying method; Applicator; Spray gun | ||
| References | ||
|
-ASTM D4541, 2002, Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers, Annual Book of ASTM Standard.
-Bodig, J. and Jayne, BA., 1989. Mechanics of wood and wood composite, translation by Ebrahimi G. Tehran: Tehran University Press.
-Bulian, F. and Graystone, J. A., 2009. Industrial Wood Coatings. Theory and practice, Eiselvier BU Amsterdam–Oxford, 33-37.
-Chin, J., Byrd, E., Martin, J. and Nguyen, T., 2005.Validation of the Reciprocity Law for Coating Photo degradation, J. Coat. Technol. Res., 2 (7): 499–508.
-Derbyshire, H. and Miller, E. R., 1981. The photodegradation of wood during solar irradiation. Holz als Roh-und Werkstoff, 39(8): 341-350.
-Ghofrani, M. and Khojasteh Khosro, S., 2014. The effect of wood surface finishing quality on the adhesion strength of clear coat. Journal of Color Science technology 7: 339-345.
-Gholamiyan, M. Tarmian, A. and Azadfallah, H., 2010, Gas and Water Permeability of Poplar Wood Coated with Sealer and Nitrocellulose Lacquer, Polyester Lacquer and Nano-particles. Journal of Forest and Wood Products, 63(3): 281-291.
-Hon, D. N. S. and Feist, W. C., 1981. Free radical formation in wood: the role of water. Wood Science.
-Khojasteh Khosro, S., 2014. Investigation on the effect of nano Zinc Oxide on physical properties of polyurethane clear coat in wooden furniture surfaces. Master's thesis, Wood Science and Technology Department, Shahid Rajaee Teacher Training University, Tehran, 95p.
-Kureli, I., 1996. Search on Application Possibility of Chip-wood and Fiber Plates over Wet Surface, PhD Thesis, Department of Furniture and Decoration, Gazi University, Ankara,
-Keshani langerodi, A., 2006. Comparing the performance of polyester, half polyester cover and a clear sealer on wood furniture and functional properties of beech plywood, Master's thesis, Faculty of Natural Resources, University of Tehran, Iran,
-Kaygin, B. and Akgun, E., 2008. Comparison of conventional varnishes with nanolake UV varnish with respect to hardness and adhesion durability, Int. J.Mol.Sci., 9: 476-485.
-Latibari, A., 2007. Science and technology of adhesion for lignocellulosic substances, Daneshgahe azad eslami, Karaj, 348p.
-Manavi, GH., Ghofrani, M. and Mirshokraei, S.A., 2012. Effects of wood type, moisture content and paint type on adhesion strength of conventional clear paints used in furniture manufacture. Iranian J. Wood Sci. Re., 27: 743-753.
-Nazerian, M., 2012. Protective and decoration coating of wood and wood product, Jahad University.
-Ozcifci, A., 2006. Effects of boron compounds on the bonding strength of phenol-formaldehyde and melamine-formaldehyde adhesives to impregnated wood materials. Journal of adhesion science and technology, 20(10): 1147-1153.
-Rehn, P., Wolkenhauer, A., Bente, M., Förster, S. and Viöl, W., 2003. Wood surface modification in dielectric barrier discharges at atmospheric pressure.Surface and Coatings Technology, 174: 515-518.
-Sjostrom, E., 1993. Wood Chemistry Fundamentals and Applications, Gulf Professional Publishing.
-Sonmez, A. Budakci, M. and Bayram, M., 2009. Effect of wood moisture content on adhesion of varnish coatings, Scientific Research and Essay. 4: 1432-1437.
-Sonmez, A., Budakci, M. and Pelit, H., 2011. The effect of the moisture content of wood on the layer performance of water-borne varnishes. BioResources, 6: 3166-3178.
-Stamm, A. J., 1956. Thermal degradation of wood and cellulose. Industrial & Engineering Chemistry, 48(3): 413-417.
-Sarmadi, A. and Kardan, SM., 2011. Complete reference of wooden stractures, Tehran: Motafakeran press,
-Unger, A., Schniewind, AP. And Unger, W. 2011.Conservation of wood artifacts, translation by Tarmian, A. and Karimi, AN. Tehran: Tehran University Press. | ||
|
Statistics Article View: 1,553 PDF Download: 691 |
||
Journal management system. designed by sinaweb